evinrude 30 hp outboard for sale

Evinrude 30 HP Buying Guide: Specs, Prices and Best Models in Stock

If you’re after a small motor with real punch, have a look at our Evinrude 30 HP outboard for sale. It’s the E-TEC E30DPGL in graphite. It weighs 181 pounds, starts with the key or a rope, has power trim, and runs clean. We’ve tested it in our shop and we ship it to buyers all over the world.

I’ve laid out everything you need below: specs, how it runs, which boats it suits, what it costs to own, and how ordering works. Jump to any part using the contents.

Want to see the rest of the range first? Our Evinrude E-TEC outboard for sale guide lays out every size we have, with specs and prices side by side.

evinrude 30 hp outboard for sale

What You’re Getting

The E30DPGL is a 30 horsepower, two-cylinder E-TEC direct injection two-stroke. It shares its 577 cc block with the E-TEC 25, tuned for a bit more power. It has a 20 inch shaft, electric start with a rope backup, power trim and tilt, and remote steering with a tiller option. At the time of writing it’s listed at around $3,501.

For a lot of small boats, 30 HP is the point where things go from “it’ll do” to “this is fun”. That’s why an Evinrude 30 HP outboard for sale in good shape gets plenty of attention.

Evinrude 30 HP Outboard for Sale: E30DPGL Specifications

Engine modelE30DPGL, graphite
Horsepower30 HP
Engine typeInline 2-cylinder E-TEC direct injection, 2-stroke
Bore x stroke2.992 x 2.5 in (76 x 64 mm)
Displacement35.2 cu in (577 cc)
Gear ratio2.15:1
Full throttle RPM5,500 to 6,000 RPM
Weight181 lbs (82 kg)
StartingElectric and rope
ControlsMechanical
Fuel inductionE-TEC direct injection with stratified low RPM combustion
Alternator56 amps total, 15 amps net dedicated
SteeringRemote (tiller available)
TrimPower trim and tilt
Trim range-4 to 16 degrees
Tilt range65 degrees
Shaft length20 in (508 mm)
LubricationMulti-point targeted oiling
Oil tankAbout 1.6 L on-board
Recommended oilEvinrude/Johnson XD100
Recommended fuel87 octane
EmissionsEPA, CARB 3 Star, European Union

Power trim on a 30 is a real bonus. Most motors this size make you tilt by hand. Here you can trim the bow down to get on plane and trim up for speed, all with a button. The rope backup means a flat battery won’t leave you stranded.

Why the E-TEC 30 Has Such a Following

Talk to people who own one and you hear the same things. It starts first time. It doesn’t smoke. It pulls harder than you’d expect. And there’s almost nothing to do to it apart from flushing and basic checks.

It also sits in a sweet spot on weight. At 181 pounds it’s light enough not to drag the stern of a small boat down, but it has the power to plane a loaded 16 footer. A lot of owners say it’s the best small motor they’ve had.

How It Runs

Turn the key or give the cord a pull and it fires. It idles smoothly and quietly, and shifts into gear without a clunk.

On a 14 to 16 foot aluminum boat with a couple of people, it pops up on plane quickly and cruises happily. The extra 5 horsepower over the 25 is noticeable when the boat’s loaded or you’re running into a chop.

Trolling is where the E-TEC really shines. The stratified low RPM mode burns a small, clean charge at idle, so the motor can crawl along for hours without fouling a plug. Old two-strokes hated that. This one doesn’t mind at all.

The Tech Behind It, Explained Simply

An old carbureted two-stroke mixed oil into the fuel and pushed it through the crankcase. Some of it went out the exhaust unburned, which is where the smoke, smell, and thirst came from.

The E-TEC fires fuel straight into the cylinder under high pressure after the exhaust port closes. Nothing escapes. Oil comes from a separate tank in small, measured amounts. At low RPM, it burns a small concentrated charge right at the plug.

You end up with a two-stroke that’s light and punchy but runs clean enough to meet strict US and European emissions rules. That’s the whole reason this Evinrude 30 HP outboard for sale is worth considering over an older motor.

Which Boats Suit an Evinrude 30 HP Outboard for Sale?

First check your capacity plate for max horsepower and weight. Stay within it. The U.S. Coast Guard boating safety site explains this clearly.

Good matches:

  • 14 to 16 foot aluminum fishing boats rated for 30 HP
  • Jon boats and flat-bottom utility boats
  • RIBs and inflatables rated for 30 HP
  • Larger yacht tenders
  • Small skiffs and duck boats
  • Small pontoons on calm water

It has a 20 inch shaft. Measure your transom before ordering. If it’s closer to 15 inches, you’ll need a short shaft model, so send us the number if you’re unsure.

Who Buys the E-TEC 30

Anglers. Small aluminum boats rated for 30 HP, lots of trolling, early starts. It’s a perfect match.

Tender owners. A 30 on a larger RIB gets a full load ashore quickly. Easy starts and clean running matter when you use it every day.

Hunters. Cold-morning starts and a rope backup make it popular for duck boats.

Working boats overseas. In many coastal communities, 30 HP is the standard working size for small fishing boats. We ship plenty of these abroad, because a tested Evinrude 30 HP outboard for sale from us usually costs much less than a new motor bought locally after duty.

What We Test Before Any Evinrude 30 HP Outboard for Sale Ships

  1. Cold start on the key and by rope.
  2. Idle quality and warm restart.
  3. Compression on both cylinders.
  4. Evinrude Diagnostics read for hours, faults, and history.
  5. Water pump output and running temperature.
  6. Gear oil drained and inspected.
  7. Shift and power trim tested.
  8. Visual check for corrosion, cracks, and wiring issues.

We fix what we find or tell you about it first.

Why Buy Your Evinrude 30 HP Outboard for Sale From Us

Tested before listing

No untested motors. You know exactly what’s coming.

Worldwide shipping

North America, Europe, Asia, Oceania, Africa, the Middle East, South America, and the Caribbean. Crated properly, shipping quoted up front.

Honest help

Ask anything through our contact page. See what other buyers said on our reviews page.

Fair price

Today’s price is on the Evinrude 30 HP E30DPGL product page.

Other Evinrude 30 HP Motors We Stock

We usually carry a good range of 30s. Pick the setup that suits your boat:

evinrude 30 hp outboard for sale 30 HP E-TEC
Evinrude 30 HP E-TEC
evinrude 30 hp outboard for sale E30DRSL
Evinrude E30DRSL
evinrude 30 hp outboard for sale E30DTSL
Evinrude E30DTSL

You’ll find every Evinrude 30 HP outboard for sale on our Evinrude 30 HP category page. The 25 HP and 40 HP ranges are close by, and the full Evinrude range is here.

Reading the Model Codes

  • E Evinrude
  • 30 horsepower
  • D engine family
  • P power trim and tilt
  • R remote steering with manual tilt
  • T tiller
  • G graphite, S white
  • L 20 inch shaft. No L usually means a 15 inch short shaft

So if you’re comparing one Evinrude 30 HP outboard for sale with another, those letters tell you steering, tilt, color, and shaft length at a glance.

25 HP or 30 HP?

The E-TEC 25 and 30 share the same block and the same 181 pound weight. The 30 simply makes more power. So there’s no weight penalty for choosing the 30. The only real question is your boat’s rating.

If your boat is rated for 30 HP, take the 30. You’ll appreciate the extra punch with a load aboard. If it’s rated for 25, go with the 25, and we have a separate guide for that one.

E-TEC 30 vs a 30 HP Four-Stroke

Why the E-TEC

  • Strong torque for quick planing
  • Power trim and rope backup in one package
  • No oil changes
  • Long service intervals, rated at 300 hours or three years
  • Clean trolling
  • Lower cost for a tested unit

Why a four-stroke

  • A new factory warranty
  • Bigger dealer network in some places

If you’re happy doing basic upkeep, this Evinrude 30 HP outboard for sale is the smarter spend.

Tiller or Remote

This one is set up for remote steering. If your boat has no console and you steer from the stern, you’ll want a tiller. A tiller setup is available, or you can pick one of our tiller models like the E30DTSL. Tell us which you want before ordering.

Getting the Prop Right

You want 5,500 to 6,000 RPM at full throttle with your usual load. Below that, go down in pitch. Above it, go up. On a loaded workboat, lower pitch helps it pull. On a light skiff, higher pitch gives more top speed. We’ll suggest a starting prop for your boat.

Running Costs

Fuel. Very economical, especially at low speed.

Oil. The small tank lasts a good while.

Maintenance. Plugs, impeller, gear oil, anodes, and grease.

Resale. Clean E-TEC 30s hold their value well.

Saltwater Care

Lots of 30s live on the coast. Flush after every trip using the flush port. Rinse the outside, especially the clamp brackets and steering. Spray a corrosion inhibitor under the cowling now and then. Check the anodes often. If it sits on a tender in the water, tilt it up when not in use.

Checking Any Used Evinrude 30 HP Outboard for Sale

  • Diagnostic report. Hours, usage, and faults.
  • Compression. Both cylinders close together.
  • Overheats. Shown in the engine log.
  • Gear oil. Clean, no water or metal.
  • Corrosion. Around clamps and lower unit.
  • Test run. Starts by key and rope, idles steadily, shifts smoothly.

We check all of this before any motor ships.

The E-TEC 30 as a Tender Motor

Big RIB tenders take a beating. They’re launched and pulled up constantly, left sitting in salt air, and expected to start first pull when you need to get ashore. The E-TEC 30 handles that life well.

It starts easily on the key, and if the tender battery is flat there’s still the rope. Power tilt lifts the leg when you beach. The clean running means no oily film on the tender floor or the swim platform, and no fumes in your guests’ faces.

On a 3.5 to 4.5 metre RIB rated for 30 HP, it gets a full load up and moving quickly. If you run a yacht or a charter boat and need a dependable tender motor, an Evinrude 30 HP outboard for sale like this is a strong choice.

Fuel Habits Worth Keeping

Most rough running and hard starting on small outboards comes back to fuel. These habits prevent nearly all of it:

  • Use fresh fuel. Ethanol blends go stale in a few weeks.
  • Fit a water-separating filter between the tank and motor.
  • Keep the tank vent open.
  • Check the primer bulb and hoses for cracks each season.
  • Stabilize before storage and run it through the system.

Look after the fuel and your Evinrude 30 HP outboard for sale will start easily for years.

What’s Included

Each motor is a little different, so always confirm with us. Usually it’s the complete engine: powerhead, midsection, lower unit, and cowling. Some units come with a prop. Controls, cables, and gauges depend on the listing. If you already have Evinrude controls you may be able to reuse them. Tell us what’s on your boat and we’ll give you a straight list of anything else you’ll need.

First-Time E-TEC Owner Questions

Do I mix oil in the fuel? No. The oil tank feeds the engine automatically.

Which oil? Evinrude XD100 is what this engine is set up for.

What if the battery dies? Use the rope start. The motor will run and the alternator will charge the battery back up.

How do I winterize it? The E-TEC has an auto winterization routine that fogs the engine for you. Your manual or a shop with diagnostics can walk you through it.

These basics make owning an Evinrude 30 HP outboard for sale from us easy from day one.

Trailering and Storage

If you trailer your boat, use a transom saver bracket to take the strain off the transom on rough roads. For winter storage, run the auto winterization mode, flush the motor, top up the oil tank, add stabilizer to the fuel, and leave the motor tilted down so water drains from the lower unit. It’ll be ready to go when the season starts again.

Parts and Support

Evinrude stopped making outboards in 2020. BRP said it would continue supporting owners with parts and service. The 30 shares most parts with the 25 and many with the 15, so water pump kits, plugs, anodes, thermostats, and seals are widely available. For more on the brand, see this history of Evinrude outboard motors.

Keeping It in Shape

  1. XD100 oil.
  2. Fresh water flush after salt.
  3. Fuel stabilizer if it sits.
  4. Tell-tale check every start.
  5. Grease every season.
  6. Anodes at half worn.
  7. Auto winterize before storage.
  8. Pull the rope now and then so the recoil stays free.

BoatUS has helpful outboard care guides.

Rigging Tips

  • Anti-ventilation plate about level with the bottom of the hull to start.
  • A small marine starting battery is plenty.
  • Prop for 5,500 to 6,000 RPM.
  • Mechanical controls to suit Evinrude, or a tiller.
  • Diagnostics after install.

Discover Boating has beginner guides if you need them.

When the Crate Turns Up

  1. Check the crate before signing. Photograph and note any damage.
  2. Unpack carefully, keeping the motor upright if possible.
  3. Make sure everything we listed is there.
  4. Mount it and connect the controls or tiller and the battery.
  5. Fill the oil tank with XD100.
  6. Connect diagnostics to confirm the oil setting.
  7. Start it on muffs or in the water and check for a steady tell-tale.

If anything’s off, contact us straight away and we’ll help. We want every Evinrude 30 HP outboard for sale we ship to end up on the water, not sitting in a shed.

Ordering Your Evinrude 30 HP Outboard for Sale

  1. Visit the E30DPGL product page and add it to your cart, or message us first.
  2. We confirm the motor and quote shipping.
  3. You pay at checkout.
  4. We crate, ship, and send tracking.
  5. You rig it and go.

Read our refund and return policy and terms and conditions before ordering.

Shipping and customs

Around a week for most of North America after dispatch. Overseas orders usually go by sea to your nearest port, with air freight as a faster option. At 181 pounds, it’s cheaper to ship than bigger motors. Duties are set by your country, and we provide the customs paperwork.

FAQ: Evinrude 30 HP Outboard for Sale

Can I start it by hand?

Yes, it has electric start and a rope backup.

Is it a two-stroke?

Yes, a clean direct injection two-stroke.

Can this Evinrude 30 HP outboard for sale be used with a tiller?

Yes, a tiller setup is available.

Will it fit my inflatable?

If it’s rated for 30 HP with a 20 inch transom, yes.

Do you ship worldwide?

Yes. Give us your location for a quote.

How long will it last?

With good care, well over 1,000 hours is normal, and many go much further.

More Evinrude Guides

Browse our shop, accessories, or read about us.

Also in stock right now: Evinrude 30hp E30drs Outboard Motor, Evinrude 30hp E30drg Outboard Motor. Ask us if you want help comparing them.

Final Word on This Evinrude 30 HP Outboard for Sale

Light, punchy, clean, and easy to live with, with power trim and a rope backup. This Evinrude 30 HP outboard for sale is one of the best small motors ever built, and it’s tested and ready to ship.

If it suits your boat, grab it. Questions? Message us.

Order the Evinrude 30 HP outboard for sale now.

Add a Comment

Your email address will not be published. Required fields are marked *