EVINRUDE 15HP E15RGL4 OUTBOARD MOTOR

Description

We have the Evinrude E15RGL4 for sale here, a used 15 HP Evinrude four stroke outboard that has been tested in our shop before listing. Evinrude stopped building outboards in 2020, so good running examples are getting harder to find every year.

We sell outboards to boat owners, fishing guides, resorts and dealers, and we ship worldwide. Tell us where you are and we send a delivery quote before you pay anything. We also send photos of the exact motor and its model plate.

Everything is on this page: specifications, what the model code means, boats it suits, how it runs, maintenance, delivery and a short FAQ.

Evinrude E15RGL4 for sale: Specifications

Figures are for the 15 HP four stroke family. Details can vary by model year, so we check the plate on this motor before we confirm your order. Evinrude owner and operator guides are available on the BRP operator guides site.

What the Model Code on the Evinrude E15RGL4 for sale Means

Evinrude codes start with E and the horsepower. In E15RGL4, G means graphite paint; R means rope start; L means a 20 inch long shaft; the 4 at the end marks a four stroke. Other letters mark the model series and factory options. Before you pay, we read the full model and serial plate on the bracket and send you a photo, so nothing is left to guesswork.

Inside the Evinrude E15RGL4 for sale

The small Evinrude four strokes were built for Evinrude by Tohatsu, one of the oldest outboard makers in Japan. The engine in the E15RGL4 is the same proven carburettor four stroke that Tohatsu sells under its own name, painted and badged for Evinrude. That is good news today, because Tohatsu dealers and parts suppliers are everywhere.

There is no computer, no injection pump and no sensors to chase. If you can change a spark plug and clean a carburettor, you can keep this motor running for years. Oil lives in a sump and gets changed once a season, the same way you would on a lawn mower or a car.

The 351 cc twin is the biggest of the small Evinrude four strokes. It is strong enough to plane a light aluminium boat and still light enough for two people to lift.

Tohatsu Parts Fit the Evinrude E15RGL4 for sale

Because the E15RGL4 was built by Tohatsu, most service parts are shared with the matching Tohatsu MFS15 model of the same years. Impellers, spark plugs, filters, carburettor kits, gaskets and many gearcase parts cross over, and parts catalogues often list the Evinrude and Tohatsu numbers side by side. That makes this motor easy to keep running in places where Evinrude dealers have closed but Tohatsu dealers are common.

When you order parts, give the supplier the full Evinrude model code and serial number from the bracket plate. If they only stock Tohatsu, ask them to look up the matching MFS15 part for the same model year. A good parts counter can do this in minutes.

Owner guides and service information for the E15RGL4 are still easy to find, and the engine is simple enough that most jobs need only basic hand tools. That is a big reason small four strokes like this hold their value so well.

Boats That Suit the Evinrude E15RGL4 for sale

Check the capacity plate on your boat first and stay within its power and weight ratings. Within those limits, good matches include:

Aluminium and jon boats

Boats from about 3.5 to 4.5 m.

Inflatables and RIBs

Larger tenders rated for this power.

Kicker motor

A trolling and back up engine beside a bigger main motor.

Sailboat auxiliary

Small keelboats that need reverse for docking.

How the Evinrude E15RGL4 for sale Runs

Choke out from cold, a couple of pulls or a turn of the key on electric start versions, and the Evinrude E15RGL4 for sale settles into a steady idle. It is quiet, smoke free and easy on fuel. Trolling is smooth, and there is no oil to mix in the tank.

Choosing Between 15 HP Evinrude Models

We usually have more than one 15 HP Evinrude in stock. They differ in start type, steering, trim, colour and shaft length, so pick the one that matches your boat and how you use it. If you are not sure, send us your transom height, boat length and usual load, and we will recommend the right one.

You can also look at our tested 15 HP Evinrude, which has a full write-up of how we inspected it.

Why Buy a Used Evinrude

Evinrude closed its outboard line in 2020, so there is no factory replacement for the Evinrude E15RGL4 for sale. The nearest new alternative is a 15 HP four stroke from another brand, which usually costs much more once you add rigging. A tested used Evinrude gives you a proven motor for a fraction of that price.

BRP, the company behind Evinrude, kept supplying parts after production ended, and independent dealers and parts suppliers carry everything from impellers to injectors. Mechanics around the world know these motors well.

A Short History of Evinrude

Ole Evinrude built one of the first practical outboard motors in the early 1900s, and the name has been on transoms ever since. Over the decades Evinrude moved from simple two strokes to the E-TEC direct injection engines of the 2000s, which cut emissions and fuel use without giving up the light weight and punch of a two stroke. In 2020 BRP ended Evinrude outboard production, which is why every Evinrude for sale today, including the Evinrude E15RGL4 for sale, is a used motor.

Four Stroke or E-TEC at 15 HP?

Evinrude sold small four strokes like the E15RGL4 for buyers who wanted the simplest possible motor: a carburettor, an oil sump and nothing electronic to go wrong. They are quiet, cheap to run and easy to fix anywhere in the world. The E-TEC two strokes are lighter for their power and start very easily, but they need XD-100 oil and diagnostic software for some jobs.

Controls and Handling

With a tiller, set the steering friction so the motor holds course when you let go but turns without effort. Twist grip throttle and a clear gear lever make low speed docking easy. Remember that an outboard steers by pushing the stern sideways, so slow down early in tight marinas and give the stern room to swing.

How We Test the Evinrude E15RGL4 for sale

• Compression checked on every cylinder.
• Water pump and tell tale stream checked on a test tank.
• Gearcase oil drained and checked for water.
• Shifting, throttle and trim checked through the full range.
• Carburettor checked and cleaned if needed.

A motor that fails any of this does not get listed as ready to run. Ask us and we will send the readings we recorded for this motor.

Getting the Shaft Length Right

Measure your transom height at the centre, from the top of the transom to the bottom of the hull. About 15 inches suits a short shaft, about 20 inches a long shaft and about 25 inches an extra long shaft. The Evinrude E15RGL4 for sale has a 20 inch (long shaft), and we confirm it against your measurement before you order.

Mounting and Rigging

Centre the motor on the transom, tighten the clamp screws and check them again after the first run. Tie a safety line from the motor to the boat. Set the trim so the motor is upright at speed, with the anti-ventilation plate about level with the bottom of the hull.

Your First Day Out With the Evinrude E15RGL4 for sale

Pick a calm day and stay close to where you launched. Fit the kill cord, squeeze the fuel primer bulb until it is firm and start the motor in neutral. Watch for the stream of water from the tell tale. Run at moderate, varied throttle for the first outing rather than holding it wide open, so you catch anything that shipping or rigging might have disturbed.

Maintenance on the Evinrude E15RGL4 for sale

• Flush with fresh water after every trip in salt or dirty water.
• Change the engine oil once a season and check the level before each trip.
• Change the gear oil every season and look for milky oil.
• Replace the water pump impeller every two to three seasons.
• Check the spark plugs and fuel filter.
• Grease the swivel, tilt tube and steering points.
• Check the anodes and replace them when half worn.

Small four strokes like the Evinrude E15RGL4 for sale are simple to service at home with basic tools.

The Water Pump Impeller

Every water cooled outboard has a rubber impeller in the lower unit that pushes cooling water up to the engine. Rubber ages and sand wears the vanes, so replace it every two or three seasons, or sooner in sandy water. A weak or missing tell tale stream is the first warning. Stop the engine and find the cause, because running without cooling water can damage it quickly.

Changing the Gear Oil

Take out the lower drain screw, then the upper vent screw, and let the old oil run into a tray. Clean dark oil is normal. Milky oil means water is getting past a seal and should be fixed before it rusts the gears. Refill from the bottom hole with marine gear oil until it comes out of the top, then fit the vent screw and the drain screw with new washers.

Fuel and Carburettor Care

Use fresh 87 octane petrol and add a stabiliser if the Evinrude E15RGL4 for sale will sit for more than a few weeks. Ethanol fuel left in a motor over winter causes most starting problems. Run the carburettor dry before storage.

Salt Water Care

Flush with fresh water after every salt trip using a flushing attachment or a test tank. Rinse the outside, wipe the cowl and spray a corrosion inhibitor under the cowl now and then. Tilt the motor up when the boat is moored so the gearcase is out of the water.

Common Problems and Quick Checks

• Will not start. Check the kill cord, fuel vent, primer bulb and choke.
• Weak tell tale. Clear the outlet; if still weak, check the impeller.
• Loss of power. Check the prop for damage or weed and the fuel filter.
• Warning horn. Stop and check oil level and cooling straight away.

Running Costs

Small four strokes sip fuel and need only cheap service parts. Over a few seasons the price difference against a new motor goes a long way.

Moving From an Older Two Stroke

If you are replacing an old carburettor outboard, the Evinrude E15RGL4 for sale will feel quieter and cleaner, with no blue smoke at idle and no oil mixing at the fuel dock. As a four stroke it also has no oil in the fuel at all.

Who Buys the Evinrude E15RGL4 for sale

We ship this kind of motor to weekend boaters, anglers, fishing guides and small businesses that run boats every day. Many buyers are repowering an older boat that is not worth a brand new engine. Every order gets the same treatment: photos of the exact motor, a delivery quote and updates until it arrives.

Choosing the Right Propeller for the Evinrude E15RGL4 for sale

The right prop lets the motor reach the top of its full throttle range with your normal load aboard. If it cannot get there, the pitch is too high and the engine is working too hard. If it runs past the range, the pitch is too low and you are wasting fuel. Small boats are sensitive to load, so the prop that suits one person may feel slow with three. A prop shop can lend or swap props to help you find the sweet spot. Tell us your boat and load and we will suggest a starting pitch.

Trim for Best Performance

Trim changes the angle of the motor on the transom. Trimmed in, the bow stays down, which helps the boat get on the plane and handle chop. Trimmed out, the bow lifts, drag drops and top speed rises. With a manual tilt pin, set the angle so the boat runs level at your usual cruising speed. Move the pin one hole at a time and test again. If the prop starts to ventilate and the revs jump, you have gone too far.

Battery and Electrical Tips

A rope start motor needs no battery to run, which is one less thing to go flat. If you want lights or a fish finder, a small battery can be added and charged at home. Check wiring and connectors each season for corrosion, especially in salt water.

Winter Lay-Up and Storage

If the Evinrude E15RGL4 for sale will sit for a few months, prepare it properly. Treat the fuel with stabiliser and run the motor so treated fuel reaches the carburettor, then run it dry. Change the gear oil so no water sits in the gearcase over winter. Grease all fittings, remove the battery and keep it charged, and store the motor upright in a dry place with the cowl on.

In spring, fit a fresh plug if needed, refit the battery, check the oil and run the motor on a flushing attachment before the first trip.

Lifting and Transport

Carry the motor upright when you can. If you lay it down, follow the owner guide for the correct side, so oil and fuel stay where they belong. Close the fuel vent before you move it.

Anodes and Corrosion

Sacrificial anodes on the gearcase and bracket corrode instead of the aluminium housing. Check them each time you flush the Evinrude E15RGL4 for sale and replace them when they are worn to about half their size. Never paint them. In salt water, a set of anodes is the cheapest insurance you can buy for an outboard.

Questions to Ask Any Used Outboard Seller

Whoever you buy from, ask for compression readings on every cylinder, a photo of the model and serial plate, a video of the motor running with a strong tell tale stream, and the condition of the gear oil. Ask whether the impeller has been replaced recently. A seller who cannot answer these is asking you to take a risk. We answer all of them for the Evinrude E15RGL4 for sale before you pay.

What to Carry on Board

A spare kill cord, spare plugs and a plug spanner, a basic tool kit, a spare prop nut and pin, a bailer, life jackets and a phone in a dry bag cover most problems. Paddles or an anchor are worth carrying on any boat, because even a good motor can be stopped by a fouled prop or bad fuel.

Serial Number and Records

Write down the serial number from the bracket plate when the Evinrude E15RGL4 for sale arrives and keep a photo of it with your receipt. You will need it to order the right parts, for insurance and in some countries for registration. Keep a simple service log; it helps when you sell the boat later.

How Delivery Works

We ship worldwide. The Evinrude E15RGL4 for sale is drained, crated for its size and weight and booked with a carrier we trust or your own forwarder. We photograph the crating and send you the tracking number and paperwork, and we quote the full delivery cost to your country before you pay.

A Short Checklist Before Buying

• Transom measured for the right shaft length.
• Capacity plate checked for power and weight.
• Controls, battery and rigging plan made.
• Delivery address sent to us.

Buying the Evinrude E15RGL4 for sale From Us

The price is on this page. Before we ship, we send photos and a delivery quote. Our refund and return policy and terms and conditions are on the site. Read what other buyers say on our reviews page, learn more on our about us page, or go to the contact page. For a full buying guide, read our Evinrude 15 HP outboard for sale article.

Other Evinrude Outboards to Compare

• Evinrude E15RG4 for sale
• Evinrude E15TEG4 for sale
• Evinrude E15HPSL for sale
• Evinrude E15HPSX for sale
• All 15 HP Evinrude outboards
• All Evinrude outboards
• Evinrude outboard buying guide
• The full shop

FAQ: Evinrude E15RGL4 for sale

Is the Evinrude E15RGL4 for sale new or used?

Used, and tested in our shop before listing.

What engine does it have?

4-stroke, 2 cylinder, carburettor (built for Evinrude by Tohatsu), 351 cc (21.4 cu in).

How does it start?

Manual rope start.

What shaft length is it?

20 inch (long shaft).

Can I still get parts?

Yes. BRP and independent suppliers carry parts worldwide.

How much does the Evinrude E15RGL4 for sale weigh?

About 52 to 54 kg (114 to 120 lb) depending on version.

Can I see the Evinrude E15RGL4 for sale running before I pay?

Yes. Ask and we will send a video of it running on our test tank with the tell tale stream visible.

What steering does it use?

Tiller handle.

Is the Evinrude E15RGL4 for sale a good repower?

For boats rated for 15 HP, yes. Send us your boat details and we will check the fit.

Do you ship the Evinrude E15RGL4 for sale worldwide?

Yes. Send us your location and we will quote delivery.

Final Word

If you want a proven 15 HP Evinrude at a fair price, the Evinrude E15RGL4 for sale is a smart choice. Order today, or message us first with your boat details and we will make sure it is the right fit.