EVINRUDE 25HP E25DGTL OUTBOARD MOTOR

Description

We have the Evinrude E25DGTL for sale here, a used 25 HP Evinrude E-TEC outboard that has been tested in our shop before listing. Evinrude stopped building outboards in 2020, so good running examples are getting harder to find every year.

We sell outboards to boat owners, fishing guides, resorts and dealers, and we ship worldwide. Tell us where you are and we send a delivery quote before you pay anything. We also send photos of the exact motor and its model plate.

Everything is on this page: specifications, what the model code means, boats it suits, how it runs, maintenance, delivery and a short FAQ.

Evinrude E25DGTL for sale: Specifications

Figures are for the 25 HP E-TEC family. Details can vary by model year, so we check the plate on this motor before we confirm your order. Evinrude owner and operator guides are available on the BRP operator guides site.

What the Model Code on the Evinrude E25DGTL for sale Means

Evinrude codes start with E and the horsepower. In E25DGTL, G means graphite paint; T means tiller steering; L means a 20 inch long shaft. Other letters mark the model series and factory options. Before you pay, we read the full model and serial plate on the bracket and send you a photo, so nothing is left to guesswork.

E-TEC Direct Injection: What It Means on the Evinrude E25DGTL for sale

The E25DGTL is an Evinrude E-TEC, a two stroke with direct fuel injection. Instead of a carburettor mixing fuel and oil, an injector sprays fuel straight into each cylinder at exactly the right moment. At low speed the engine switches to a lean, stratified mode that keeps idle and trolling clean.

In practice that means quick starts, no smoke, strong low down torque and fuel use close to a modern four stroke. There are no valves to adjust and no carburettors to gum up over the winter. Oil comes from a separate reservoir and the engine meters it for you, so you never mix fuel by hand.

The E-TEC 25 and 30 share one 577 cc twin cylinder block, introduced in 2009. The 30 is the same motor with more power dialled in, so both weigh about the same. Weight runs from about 150 lb for a basic rope start tiller to about 187 lb with electric start and power trim.

Boats That Suit the Evinrude E25DGTL for sale

Check the capacity plate on your boat first and stay within its power and weight ratings. Within those limits, good matches include:

Aluminium fishing boats

Boats from about 4 to 5 m that need to plane with gear aboard.

Skiffs and work boats

Light commercial boats that run every day.

RIBs

Mid size RIBs rated for 25 to 30 HP.

How the Evinrude E25DGTL for sale Runs

The Evinrude E25DGTL for sale fires quickly and settles into a quiet idle with no smoke. Open the throttle and the direct injection torque pushes the boat onto the plane fast. At cruise it is smooth, and at trolling speed it runs clean for hours without fouling plugs.

Choosing Between 25 HP Evinrude Models

We usually have more than one 25 HP Evinrude in stock. They differ in start type, steering, trim, colour and shaft length, so pick the one that matches your boat and how you use it. If you are not sure, send us your transom height, boat length and usual load, and we will recommend the right one.

You can also look at our tested 25 HP Evinrude, which has a full write-up of how we inspected it.

Why Buy a Used Evinrude

Evinrude closed its outboard line in 2020, so there is no factory replacement for the Evinrude E25DGTL for sale. The nearest new alternative is a 25 HP four stroke from another brand, which usually costs much more once you add rigging. A tested used Evinrude gives you a proven motor for a fraction of that price.

BRP, the company behind Evinrude, kept supplying parts after production ended, and independent dealers and parts suppliers carry everything from impellers to injectors. Mechanics around the world know these motors well.

A Short History of Evinrude

Ole Evinrude built one of the first practical outboard motors in the early 1900s, and the name has been on transoms ever since. Over the decades Evinrude moved from simple two strokes to the E-TEC direct injection engines of the 2000s, which cut emissions and fuel use without giving up the light weight and punch of a two stroke. In 2020 BRP ended Evinrude outboard production, which is why every Evinrude for sale today, including the Evinrude E25DGTL for sale, is a used motor.

E-TEC or Four Stroke at 25 HP?

Compared with a four stroke of the same power, the E-TEC is usually lighter, with more torque low in the rev range and no oil changes or valve adjustments. Four strokes are a little quieter at cruise and use engine oil rather than injected two stroke oil. For a repower on an older hull, the lower weight of the E-TEC is often the deciding factor.

Controls and Handling

With a tiller, set the steering friction so the motor holds course when you let go but turns without effort. Twist grip throttle and a clear gear lever make low speed docking easy. Remember that an outboard steers by pushing the stern sideways, so slow down early in tight marinas and give the stern room to swing.

How We Test the Evinrude E25DGTL for sale

• Compression checked on every cylinder.
• Water pump and tell tale stream checked on a test tank.
• Gearcase oil drained and checked for water.
• Shifting, throttle and trim checked through the full range.
• Oil injection cycled and the engine read with Evinrude diagnostics.

A motor that fails any of this does not get listed as ready to run. Ask us and we will send the readings we recorded for this motor.

Getting the Shaft Length Right

Measure your transom height at the centre, from the top of the transom to the bottom of the hull. About 15 inches suits a short shaft, about 20 inches a long shaft and about 25 inches an extra long shaft. The Evinrude E25DGTL for sale has a 20 inch (long shaft), and we confirm it against your measurement before you order.

Mounting and Rigging

Centre the motor on the transom, tighten the clamp screws and check them again after the first run. Tie a safety line from the motor to the boat. Set the trim so the motor is upright at speed, with the anti-ventilation plate about level with the bottom of the hull.

Your First Day Out With the Evinrude E25DGTL for sale

Pick a calm day and stay close to where you launched. Fit the kill cord, squeeze the fuel primer bulb until it is firm and start the motor in neutral. Watch for the stream of water from the tell tale. Run at moderate, varied throttle for the first outing rather than holding it wide open, so you catch anything that shipping or rigging might have disturbed.

Maintenance on the Evinrude E25DGTL for sale

• Flush with fresh water after every trip in salt or dirty water.
• Top up the oil reservoir with XD-100 oil. There is no crankcase oil to change on an E-TEC.
• Change the gear oil every season and look for milky oil.
• Replace the water pump impeller every two to three seasons.
• Check the spark plugs and fuel filter.
• Grease the swivel, tilt tube and steering points.
• Check the anodes and replace them when half worn.

Evinrude designed the E-TEC to go a long time between dealer services, often quoted as three years or 300 hours of normal use. Most owners do the simple jobs above themselves.

The Water Pump Impeller

Every water cooled outboard has a rubber impeller in the lower unit that pushes cooling water up to the engine. Rubber ages and sand wears the vanes, so replace it every two or three seasons, or sooner in sandy water. A weak or missing tell tale stream is the first warning. Stop the engine and find the cause, because running without cooling water can damage it quickly.

Changing the Gear Oil

Take out the lower drain screw, then the upper vent screw, and let the old oil run into a tray. Clean dark oil is normal. Milky oil means water is getting past a seal and should be fixed before it rusts the gears. Refill from the bottom hole with marine gear oil until it comes out of the top, then fit the vent screw and the drain screw with new washers.

Fuel and Oil Care

Use fresh 87 octane petrol and add a stabiliser if the Evinrude E25DGTL for sale will sit for more than a few weeks. Ethanol fuel left in a motor over winter causes most starting problems. Use XD-100 oil in the reservoir; the injection system is calibrated around it. Before storage, run the E-TEC winterising procedure from the owner guide, which fogs the engine automatically.

Salt Water Care

Flush with fresh water after every salt trip using a flushing attachment or a test tank. Rinse the outside, wipe the cowl and spray a corrosion inhibitor under the cowl now and then. Tilt the motor up when the boat is moored so the gearcase is out of the water.

Common Problems and Quick Checks

• Will not start. Check the kill cord, fuel vent, primer bulb and choke.
• Weak tell tale. Clear the outlet; if still weak, check the impeller.
• Loss of power. Check the prop for damage or weed and the fuel filter.
• Warning horn. Stop and check oil level and cooling straight away.

Running Costs

E-TEC engines use far less fuel than old carburettor two strokes, and close to a four stroke of the same power. There are no oil changes, belts or valves, so service costs stay low. Over a few seasons the price difference against a new motor goes a long way.

Moving From an Older Two Stroke

If you are replacing an old carburettor outboard, the Evinrude E25DGTL for sale will feel quieter and cleaner, with no blue smoke at idle and no oil mixing at the fuel dock. Oil is injected automatically from a reservoir, so you only top it up.

Who Buys the Evinrude E25DGTL for sale

We ship this kind of motor to weekend boaters, anglers, fishing guides and small businesses that run boats every day. Many buyers are repowering an older boat that is not worth a brand new engine. Every order gets the same treatment: photos of the exact motor, a delivery quote and updates until it arrives.

Choosing the Right Propeller for the Evinrude E25DGTL for sale

The right prop lets the motor reach the top of its full throttle range with your normal load aboard. If it cannot get there, the pitch is too high and the engine is working too hard. If it runs past the range, the pitch is too low and you are wasting fuel. Small boats are sensitive to load, so the prop that suits one person may feel slow with three. A prop shop can lend or swap props to help you find the sweet spot. Tell us your boat and load and we will suggest a starting pitch.

Trim for Best Performance

Trim changes the angle of the motor on the transom. Trimmed in, the bow stays down, which helps the boat get on the plane and handle chop. Trimmed out, the bow lifts, drag drops and top speed rises. With a manual tilt pin, set the angle so the boat runs level at your usual cruising speed. Move the pin one hole at a time and test again. If the prop starts to ventilate and the revs jump, you have gone too far.

Battery and Electrical Tips

A rope start motor needs no battery to run, which is one less thing to go flat. If you want lights or a fish finder, a small battery can be added and charged at home. Check wiring and connectors each season for corrosion, especially in salt water.

Winter Lay-Up and Storage

If the Evinrude E25DGTL for sale will sit for a few months, prepare it properly. Treat the fuel with stabiliser and run the motor so treated fuel reaches the injectors, then follow the storage procedure in the owner guide. Change the gear oil so no water sits in the gearcase over winter. Grease all fittings, remove the battery and keep it charged, and store the motor upright in a dry place with the cowl on.

In spring, fit a fresh plug if needed, refit the battery, check the oil and run the motor on a flushing attachment before the first trip.

Lifting and Transport

Carry the motor upright when you can. If you lay it down, follow the owner guide for the correct side, so oil and fuel stay where they belong. Close the fuel vent before you move it.

Anodes and Corrosion

Sacrificial anodes on the gearcase and bracket corrode instead of the aluminium housing. Check them each time you flush the Evinrude E25DGTL for sale and replace them when they are worn to about half their size. Never paint them. In salt water, a set of anodes is the cheapest insurance you can buy for an outboard.

Questions to Ask Any Used Outboard Seller

Whoever you buy from, ask for compression readings on every cylinder, a photo of the model and serial plate, a video of the motor running with a strong tell tale stream, and the condition of the gear oil. Ask whether the impeller has been replaced recently. A seller who cannot answer these is asking you to take a risk. We answer all of them for the Evinrude E25DGTL for sale before you pay.

What to Carry on Board

A spare kill cord, spare plugs and a plug spanner, a basic tool kit, a spare prop nut and pin, a bailer, life jackets and a phone in a dry bag cover most problems. Paddles or an anchor are worth carrying on any boat, because even a good motor can be stopped by a fouled prop or bad fuel.

Serial Number and Records

Write down the serial number from the bracket plate when the Evinrude E25DGTL for sale arrives and keep a photo of it with your receipt. You will need it to order the right parts, for insurance and in some countries for registration. Keep a simple service log; it helps when you sell the boat later.

How Delivery Works

We ship worldwide. The Evinrude E25DGTL for sale is drained, crated for its size and weight and booked with a carrier we trust or your own forwarder. We photograph the crating and send you the tracking number and paperwork, and we quote the full delivery cost to your country before you pay.

A Short Checklist Before Buying

• Transom measured for the right shaft length.
• Capacity plate checked for power and weight.
• Controls, battery and rigging plan made.
• Delivery address sent to us.

Buying the Evinrude E25DGTL for sale From Us

The price is on this page. Before we ship, we send photos and a delivery quote. Our refund and return policy and terms and conditions are on the site. Read what other buyers say on our reviews page, learn more on our about us page, or go to the contact page. For a full buying guide, read our Evinrude 25 HP outboard for sale article.

Other Evinrude Outboards to Compare

• Evinrude E25DTSL for sale
• Evinrude E25DGTE for sale
• Evinrude E25DPSL for sale
• Evinrude E25DRGL for sale
• All 25 HP Evinrude outboards
• All Evinrude outboards
• Evinrude outboard buying guide
• The full shop

FAQ: Evinrude E25DGTL for sale

Is the Evinrude E25DGTL for sale new or used?

Used, and tested in our shop before listing.

What engine does it have?

E-TEC direct injection 2-stroke, 2 cylinder, 577 cc (35.2 cu in).

How does it start?

Confirmed for this motor before you pay.

What shaft length is it?

20 inch (long shaft).

Can I still get parts?

Yes. BRP and independent suppliers carry parts worldwide.

How much does the Evinrude E25DGTL for sale weigh?

About 150 to 187 lb (68 to 85 kg) depending on start and trim.

Can I see the Evinrude E25DGTL for sale running before I pay?

Yes. Ask and we will send a video of it running on our test tank with the tell tale stream visible.

What steering does it use?

Tiller handle.

Is the Evinrude E25DGTL for sale a good repower?

For boats rated for 25 HP, yes. Send us your boat details and we will check the fit.

Do you ship the Evinrude E25DGTL for sale worldwide?

Yes. Send us your location and we will quote delivery.

Final Word

If you want a proven 25 HP Evinrude at a fair price, the Evinrude E25DGTL for sale is a smart choice. Order today, or message us first with your boat details and we will make sure it is the right fit.